lying_in_wait
member
Reged: 12/14/05
Posts: 1637
Loc: Choot 'Em!
|
|
Well the MacGyver Motor 06 was a fun project and it turned out great. Took me a while to build since I had to figure things out as I went along.
This year I decided to make a smaller version for my Dad. So MacGyver Motor 07 will be 2.8 HP. I decided to wait until I had all of the parts in hand before starting the build. I now have everything and fully anticipate building the whole thing in a day. Now finding a day to do it is another story, maybe Sunday??
I scouted around for deals and had to hunt down a few odd sized items, but heres a breakdown of what I've got in it.
*2.8 HP Lifan (Honda knock off) 4 stroke engine. Removed from a demo bike at a mini bike dealer. Has been run but is new. $53 from ebay.
*6" bronze prop. Used but in great condition and very stout. $41 on ebay.
*Steel. DOM tube for shaft and bearing housings, stainless drive shaft, angle and flat stock for frame. $60 at Metal By The Foot.
*U-joint. 2 yokes, cross bearing, 2 weld in hubs $70 total at Tractor Supply.
*3 bronze bushings $3 each.
*Upper bearing $5
*Grease seals $12
*Assorted hardware $10 (retaining ring, zerk, set screws, nuts and bolts, hinge and bolt for swivel mount).
*Tubing for tiller, bicycle brake lever and cable for throttle (not pictured) Free because I already had them sitting around.
Total $260
-------------------- Shawn Wheaton
Missouri Waterfowl Association
Westside Chapter Chairman
|
DMac
member
Reged: 12/14/05
Posts: 2086
Loc: looking for my Swingline stapl...
|
|
Sammich motor
You gonna weld the tiller in place before you give it to your dad.......or after?
-------------------- Police say alcohol may have been involved in this incident
|
lying_in_wait
member
Reged: 12/14/05
Posts: 1637
Loc: Choot 'Em!
|
|
Quote:
DMac said: Sammich motor
Maybe so, but sumpin tells me that he won't be rebuilding a carb whilst standing waist deep at the ramp.
And after of course, gotta keep things interesting ya'know.
-------------------- Shawn Wheaton
Missouri Waterfowl Association
Westside Chapter Chairman
|
Bandito
member
Reged: 12/14/05
Posts: 1065
Loc: The Lair
|
|
I'll give you $250 for it... after you put it together, of cours.
-------------------- With my new york brim and my gold tooth displayed,
Nobody give me trouble cause they know I got it made.
|
lying_in_wait
member
Reged: 12/14/05
Posts: 1637
Loc: Choot 'Em!
|
|
Finally got a few things done and have a day to mess with the new motor. The lathe, cut off saw, angle grinder, drill press and welder are all ready to rock and MacGyver Motor '07 will be born this day. I'll be taking pics as I go along and will post within the next few days.
-------------------- Shawn Wheaton
Missouri Waterfowl Association
Westside Chapter Chairman
|
lying_in_wait
member
Reged: 12/14/05
Posts: 1637
Loc: Choot 'Em!
|
|
4:00 PM it's over half done and I didn't start till 1:00
-------------------- Shawn Wheaton
Missouri Waterfowl Association
Westside Chapter Chairman
|
DMac
member
Reged: 12/14/05
Posts: 2086
Loc: looking for my Swingline stapl...
|
|
Less yappin' and more workin'
-------------------- Police say alcohol may have been involved in this incident
|
Burrhead
member
Reged: 12/14/05
Posts: 3075
Loc: Just north of Bugtussle
|
|
What DMac said. We ain't payin' ya to play on the computer.
-------------------- Somebody has to walk the point.
|
lying_in_wait
member
Reged: 12/14/05
Posts: 1637
Loc: Choot 'Em!
|
|
dammmmitt, thats what SHE said all day yesterday
Looks like I ain't gonna finish today since it decided to rain like a mutha forker. So far I have the frame assembled, the bearing housing welded on the drive tube, the hubs welded into the U joint yokes and the cross bearing pressed together, drive shaft threaded for the prop. Still need to cut a keyway in the drive shaft, cut and weld a skeg, a tiller handle and the swivel/pivot mount. After that she'll be ready for paint and final assembly. time for a
-------------------- Shawn Wheaton
Missouri Waterfowl Association
Westside Chapter Chairman
|
lying_in_wait
member
Reged: 12/14/05
Posts: 1637
Loc: Choot 'Em!
|
|
Well I got it done except for the tiller handle and paint. Decided to wait to do the tiller until I can mount the motor on Dad's boat so I can get the tiller at a convenient height. Runs smoothly with no rattles or excessive vibration.
-------------------- Shawn Wheaton
Missouri Waterfowl Association
Westside Chapter Chairman
|
DMac
member
Reged: 12/14/05
Posts: 2086
Loc: looking for my Swingline stapl...
|
|
Quote:
lying_in_wait said: Decided to wait to do the tiller until I can mount the motor on Dad's boat so I can get the tiller at a convenient height.
Seems I've heard that before...
Looks good
-------------------- Police say alcohol may have been involved in this incident
|
lying_in_wait
member
Reged: 12/14/05
Posts: 1637
Loc: Choot 'Em!
|
|
Have C clamp, will travel
-------------------- Shawn Wheaton
Missouri Waterfowl Association
Westside Chapter Chairman
|
Krazy
member
Reged: 12/14/05
Posts: 4861
|
|
Cavitation plate?
|
lying_in_wait
member
Reged: 12/14/05
Posts: 1637
Loc: Choot 'Em!
|
|
Hell no, just slows ya down
-------------------- Shawn Wheaton
Missouri Waterfowl Association
Westside Chapter Chairman
|
Krazy
member
Reged: 12/14/05
Posts: 4861
|
|
You got an answer fer everything dontcha monkey boy?
|
DSG
member
Reged: 01/08/06
Posts: 175
Loc: Missouri
|
|
LIW, You "could take a TV and make it into a watch!"
Looks awesome!
-------------------- His ignorance covered the earth like a blanket. And there wasn't a single hole in it.~Mark Twain
|
lying_in_wait
member
Reged: 12/14/05
Posts: 1637
Loc: Choot 'Em!
|
|
Quote:
Krazy said: You got an answer fer everything dontcha monkey boy?
Yes I do, and just so ya don't have to ask, ...........Faulty birth control
-------------------- Shawn Wheaton
Missouri Waterfowl Association
Westside Chapter Chairman
|
hardhuntr
bill biter
Reged: 12/14/05
Posts: 412
Loc: MO
|
|
Another good lookin' little motor.
I can't believe Krazy hasn't asked for a closeup pic of your welds though. He was worried about the welds on your last motor.
-------------------- These are hardhuntr's thoughts. Eat 'em up, much yum yum.
|
Mel
member
Reged: 12/14/05
Posts: 6896
Loc: Excelsior Springs, MO
|
|
Krazy is in mourning over the Flubs............he ain't got no time to worry over welds.
-------------------- Member DU, Delta
Forgive your enemies, but never forget their names - John Kennedy
|
Krazy
member
Reged: 12/14/05
Posts: 4861
|
|
Mel...thats one thing about a cub fan...we know how to lose....got lots of practice! Thanks for your concern though.
As for those welds on the first motor...hell he already posted pictures and the motor didnt have any tires and I didnt want to ask about the oil level.....
so I thought what the hell...ask about the welds!
|